fENVIROSAFE INDUSTRIAL Refrigerant 134A & R12 Replacement, 8 CANS

Description

ENVIROSAFE INDUSTRIAL Refrigerant 134A & R12 Replacement, 8 CANS
Enviro-Safe "Industrial" R12A
Industrial R134A Replacement
R134a or R12 Substitute
DOES NOT REQUIRE EPA CERTIFICATION TO PURCHASE!!!
WORK ON YOUR OWN SYSTEM!
COLDER THAN R12 or R134a!!!!!!!!
ENVIROSAFE INDUSTRIAL  R12A
8 cans of Envirosafe INDUSTRIAL Refrigerant
R134a and R12 Replacement
Each can is 6oz. and is the equivalent to 18oz. R-12 & 16 oz. of R-134a.
If you want a SUPER COLD A/C in your automobile, then you need to use the ENVIROSAFE "Industrial" R12A.
This is our coldest refrigerant available!!
*Highly recommended for warm climates!
*For automotive and other applications.
Works for standard small A/C units, but also great for SUV's, vans, suburban's,  and systems with dual air.
**Our COLDEST refrigerant for your automotive A/C needs.
Enviro-Safe&; Industrial R134a Replacement Refrigerant is made of only the Most Pure, Quality, Refined ingredients available today.
Because Enviro-Safe&; Industrial R134a Replacement Refrigerant is so efficient, you will use up to 60% less!
*THIS REFRIGERANT IS FOR USE BY QUALIFIED HVAC & REFRIGERATION TECHNICIANS.
FOR PROFESSIONAL USE ONLY.
DO NOT MIX WITH ANY OTHER REFRIGERANT.
ENVIROSAFE "Industrial" R12A IS A direct drop in replacement for 134a and other R12 substitutes.
Enviro-Safe is ultra-efficient hydrocarbon refrigerant.
How efficient is ENVIRO-SAFE?
Extremely efficient! ENVIRO-SAFE Advanced is up to 32% more efficient than R-12 and much more efficient than R-134a. This means less wear on your refrigeration system, substantial energy savings and reduced operating costs. With ENVIRO-SAFE the compressor will only load approximately 2-3 hp. ENVIRO-SAFE Advance boiling temperature is -30.4ºF. ENVIRO-SAFE ES-12a was designed as an R-134a replacement. It just happens to work equally well in converted R-12 systems and we'll tell you how to do the conversion without robbing a bank
.
Is ENVIRO-SAFE safe?
ENVIRO-SAFE does not become caustic if contaminated with moisture or oxygen.
ENVIRO-SAFE is a better conductor of heat and requires less horsepower to compress, which reduces compressor wear and extends compressor life.
ENVIRO-SAFE does not require a compressor oil change.
ENVIRO-SAFE has a very low Global Warming Potential and a Zero Ozone Depletion Potential.
ENVIRO-SAFE is covered by OSHA Hazard Communication Standard.
Yes! ENVIRO-SAFE is an "ENVIRONMENTALLY SAFE" organic, non-toxic, non-ozone depleting hydrocarbon compound. ENVIRO-SAFE is a hydrocarbon refrigerant which has been endorsed by Greenpeace and is in full compliance with the UN Montreal Protocol. Like most organic materials ENVIRO-SAFE is flammable, but its ignition temperature is 1585ºF at both 5 psi and 0 psi (which is better than the DuPont R-134a's ignition temperature of 368ºF at 5 psi and 1411ºF at 0 psi). Nevertheless, a pine odor has been added to the product so that any leak in a refrigeration system can be readily detected. To locate the precise origin of a leak, it is recommended that a hydrocarbon detector be utilized. Most mid and higher priced conventional leak detectors will detect hydrocarbon refrigerants. In the alternative, either soap bubbles or ENVIRO-SAFE DYE CHARGE can be used. ENVIRO-SAFE DYE CHARGE is both visually detectable and responsive to black light. In a safety study, the prestigious Arthur D. Little scientists concluded that hydrocarbon refrigerants pose no significant increased risk or hazard over freeon. (copy of report available at cost of US.00)
.
How does ENVIRO-SAFE compare?
Properties
R-12
R-134a
Enviro-Safe-12a
Atmospheric Lifetime Year
130
16
less than 1
G.W.P. (CO2=.05)
3650
600
4
O.D.P. (R-12=1.0)
1.0
Thermal Performance
-8%
+12-32%
Oils Compatibility
Mineral
Synthetic
Both
Component changes or wear
No
Yes
No
Potential Corrosion
Yes
Yes
No
Toxic Thermal Decomposition
Phosgene Gas
Hydrogen Fluoride Gas
None
Long Term Health Effects
None
Tumors on testicles
None
Short Term Health Risks
None
May cause death
None
Leak Detection
Halide
Halide
Hydrocarbon
Boiling Point (f)
-21
-15
-30.4
Critical Temp. (f)
233.6
214
205
Auto-ignition (f) 0 psi
Nonflammable
1411
1585
Auto-ignition (f) 5 psi
Nonflammable
368
1585
Does ENVIRO-SAFE require retrofitting?
No! ENVIRO-SAFE is a direct drop-in R-134a replacement. It requires no retrofitting or redesigning of the refrigeration system because it is completely compatible with all the materials, hoses, O-rings, seals and oils (mineral or synthetic) in all systems. The savings can be enormous! If you have an automotive R-12 system you must change the two vehicle fittings to the 134a type fittings and properly remove any freeon in accordance with EPA procedures. According to the EPA you must also change the oil to make it a "legal" 134a system. Changing the fittings can be easily done by screwing on (over the existing R-12 fittings) 134a adapter fittings. All you will need is the two 134a adapter fittings for the vehicle year and make which should cost around 10 to 20 dollars. You DO NOT need the to "134a Kit". Pep Boys/Parts USA stores and Auto Zone carry 134a adapter fittings. In California and Nevada, Auto Parts Club also carries 134a adapter fittings. Both Castrol and Delco manufacture 134a adapter fittings.
How do I install ENVIRO-SAFE?
There are no new procedures or techniques to learn! The same equipment and gauges are used. The refrigeration system is charged in the same manner as with the refrigerant being replaced using approximately the same pressure levels. (Note: ENVIRO-SAFE Advanced pressure on the high side may run up to 15 psi lower than what your R-12 high side pressure normally is. The low side pressure should be the same as your R-12 low side pressure at any given ambient temp.) Install by weight.
The equivalency ratios are:
.33 lb. of ENVIRO-SAFE Advanced = 1 lb. of R-12;
EXAMPLE: 2.2 pounds of R12 converted to Envirosafe would be 2.2x 16oz per pound = 35.2 ounces of R12.
35.2 oz of R12 x.33=11.6 ounces of Envirosafe (2 cans)
.38 lb. of ENVIRO-SAFE Advanced = 1 lb. of R-134a;
EXAMPLE: 2.8 pounds of 134a x 16 oz per pound = 44.8 ounces. The same volume of Envirosafe weighs only .38 as much so: 44.8x.38=17.02 ounces or not quite three cans
.41 lb. of ES-22a is equivalent to 1 lb. of R-22; .40 lb. of ES-502a is equivalent to 1 lb. of R-502. ENVIRO-SAFE is completely compatible with synthetic or organic oils in all existing systems. No flushing or oil changes are required. ENVIRO-SAFE is installed as a liquid.
METHOD
NOTE - it is assumes that your system is in proper operating condition - a damaged compressor, expansion valve etc. will not be magically repaired by adding Envirosafe
1 - If system is charged, check system for leaks or defective components. Replace or repair as necessary. Determine that the system has proper type and amount of lubricant according to manufacturer's specifications.
2 - Pull vacuum to test the system for leaks but DO NOT charge under vacuum. ENVIRO-SAFE does not become caustic if some moisture is present. Charging under a high vacuum can result in an overcharge. Overcharging will result in higher than desired temperatures at the vents.
3 - Connect gauges and hoses. With ENGINE OFF, invert can and open valve to install ENVIRO-SAFE on low pressure side of compressor. INSTALL AS A LIQUID. Establish flow. After an initial minimum charge is achieved, start engine and set system to high. ADD THE BALANCE OF the product per your previous determination. ( see above to determine amounts) DO NOT OVERCHARGE! In some cases, clearing the site glass overcharges the unit. Overcharging will cause loss of cooling efficiency due to high head pressures.
4 - After verifying that the pressures and temperatures are correct, shut off compressor, disconnect gauges, install service port caps and place the ENVIRO-SAFE "stick on" tag (shipped along with each purchase) in a clearly visible area.
5 - If a system has been overcharged or has a leak and must be recharged, completely evacuate the system using reclaiming equipment (not recycling equipment) and start the charging procedure over.
Does ENVIRO-SAFE have EPA approval?
ENVIRO-SAFE is a zero ozone depleting "second generation" replacement for R-134a and all other substitutes for freeon that are non-ozone depleting. EPA's Final Rule, issued April 1, 1994, states:
"In this final rule, the Agency has determined that second generation replacements, if they are non-ozone depleting and are replacing non-ozone depleting first generation alternatives, are exempt from reporting requirements under Section 612"
If an automotive system is "first generation" (ie.- has 134a fittings and contains no freeon) it may accept a "second generation" refrigerant like ENVIRO-SAFE.
Is ENVIRO-SAFE guaranteed?
ENVIRO-SAFE is guaranteed to be ozone safe and to perform as an efficient refrigerant in all systems. ENVIRO-SAFE is guaranteed to be up to 32% more efficient than freeon. ENVIRO-SAFE is guaranteed not to become caustic if contaminated with moisture and oxygen. ENVIRO-SAFE is further guaranteed not to harm air conditioning system components or any other related mechanical equipment if installed and used according to factory directions. ENVIRO-SAFE should not be recycled and the guarantee will be voided if it is run through recycling equipment (reclaiming equipment is OK).